Soulution 550 Phono / RIAA

På lager
146.000 DKK
Leveringstid:3-4 uger

Soulution 550 Phono er med til at fastholde vinyl som et uundgåeligt musikmedie, i 20 år har det været dømt dødt, men oplever du vinyl igennem denne RIAA, så er du ikke i tvivl.

  • Gratis fragt over 750 DKK
  • Lagervarer sendes indenfor 24 timer
  • Afhentning i butik

Soulution 550 Phono er med til at fastholde vinyl som et uundgåeligt musikmedie, i 20 år har det været dømt dødt, men oplever du vinyl igennem denne RIAA, så er du ikke i tvivl.

80 dB gain without distortion

The phono stage with RIAA equalisation required for vinyl playback presents the designer with a formidable technical challenge if it is to correctly and transpar­ently handle the signal from low output moving coil cartridges. Delivering a gain of up to 80 dB (10,000 times) while remaining linear and phase-correct, the amplifier must have an ultra-wide bandwidth, (internal bandwidth 1 MHz/– 3 dB) minimal distortion, optimal channel separation and maximum linearity.

Dual-mono construction

The 550 Phono features unbalanced dual-mono construction with separate power supplies for the left and right channel, guaranteeing the least possible channel crosstalk. Both inputs of the 550 can be configured for moving magnet or moving coil cartridges, with load impedance selectable via the front panel or the remote control for each input individually. A switchable < 20 Hz rumble filter protects loudspeaker cones from potentially damaging long excursions caused by warped records.

Musicality and refinement with no limits

Noise and distortion have no place in vinyl playback, despite the challenges implicit in amplifying such low signal levels. Only then can the full potential of the medium be heard. The richness of sound colours, the dynamism, the refinement. Heard through the 550 Phono, well-produced vinyl shows why for many it is still the medium to beat, unrivalled in its ability to convey emotion and musicality.

Preamplifier grade output stage

If nothing is to be lost at the source of music, then the power supply and the output stage of a phono preamplifier have to be of the highest quality. For the 550 Phono soulution uses identical power supplies and output stages to those employed in the 520 Preamplifier. Optimized for speed and precision the 550 Phono can drive any cable.

Mains:
220 – 240 V (50 – 60 Hz)
100 – 120 V (50 – 60 Hz)

Power consumption:
< 0.5 W standby
100 W device in operation

Inputs:
2 × RCA (MC/MM configurable)

Input impedance:
MC: 10 Ω – 1000 Ω
MM: 1000 Ω – 47 kΩ and 0 – 200 pF

Outputs:
1 × balanced (XLR)
1 × unbalanced (RCA)

Frequency response (– 3 dB):
0 – 1 MHz (RIAA equalisation)

THD + N:
< 0.002% (20 Hz – 20 kHz)

Signal-to-noise ratio:
100 dB

Channel separation:
60 dB @ 1 kHz

Gain max:
MC: + 66 dB @ 1 kHz (XLR) / + 60 dB @ 1 kHz (RCA)
MM: + 55 dB @ 1 kHz (XLR) / + 49 dB @ 1 kHz (RCA)

Output impedance:
10 Ω balanced (XLR)
10 Ω unbalanced (RCA)

Output current max:
11 VRMS balanced (XLR)
5.5 VRMS unbalanced (RCA)

Output current max:
0.2 A (limited)

Dimensions:
442 × 143 × 448 mm (W × H × D)
Weight approx. 20 kg

LINK (remote turn-on):
12 V control signal